In this lesson
Fret buzz is the rattle produced when a vibrating string contacts a fret it should clear. A note may still ring, or it may die quickly. Loose hardware can also rattle, and amplified hum can be unrelated to contact with a fret.
Begin by repeating the sound on one string. Its location is useful evidence, but it does not identify the cause on its own.
Guidance source-checked on 2 November 2026.
Repeat the note before making a change
- Tune to your normal playing tuning and remove any capo for the first check.
- Play the affected string open, then fret it at the notes where you hear trouble. Listen to one note at a time. Write down the string and fret numbers, including nearby notes that ring clearly.
- Place your fingertip close behind the fret wire, on the nut side of the fret, rather than in the middle of the space. Use enough pressure to sound the note and keep other fingers clear of that string. Avoid squeezing or pulling it sideways.
- Repeat with a lighter pick stroke, then your normal attack. Keep the fretting position the same so you can hear what the change does.
- If you heard the problem in a chord, pick its strings separately. An adjacent finger touching a string can mute it or produce a poor note; that is a different observation from a string rattling against a fret.
If a placement or attack change helps, practise that movement and see whether it works in the passage you want to play. The result does not rule out setup work. A guitar’s available clearance and your playing attack both affect the amount of string noise.
Record where the problem happens
| Pattern you can repeat | Useful observation to record |
|---|---|
| Only the open string rattles | Compare it with the first few fretted notes, played individually. An open-string rattle alone does not prove a worn nut. |
| One note or a short group of frets rattles | Record the exact frets and whether notes immediately before and after ring clearly. |
| Several strings rattle across the neck | Note the tuning and whether this started after restringing, a gauge change or a change in storage. |
| Buzz appears only with a hard attack | Compare a normal passage and a lighter version. Say whether the rattle interferes with the sound you actually use. |
| A rattle seems to come from elsewhere on the guitar | Note the area without tightening unidentified screws or pressing on the bridge. A loose component can imitate string noise. |
A technician may need to check string condition, relief, action, fret condition, nut slots and hardware together. The table is a listening record, not a set of instructions to adjust one part for each symptom.
Check strings and the sound source
Look for a kink, corrosion or an unravelled winding on the affected string. Even a new string can be faulty. A replacement of the correct type and gauge can be a reasonable check when one string is suspect, using the instrument’s own restringing method. You can ask a shop to do this if you are unfamiliar with its bridge or locking system. See when to change guitar strings.
For an electric or electro-acoustic, compare the instrument’s own sound with a clean amplified sound at a comfortable volume. Note whether the rattle comes through, whether sustain is affected, and whether a continuous hum remains when the strings are still and muted. That comparison helps separate a string/contact problem from noise in the amplified system; it does not locate an electrical fault.
If the noise is only in the amplified system, follow its manufacturer’s troubleshooting guidance. Taylor’s amplified-noise guide starts with a simpler signal path. Changing neck relief will not diagnose that noise.
When to have the guitar checked
Some guitars produce a little string rattle, particularly under a hard attack. The practical issue is whether it compromises your normal playing or has changed noticeably. A note that repeatedly cuts short, a persistent local problem, or a guitar that has suddenly become difficult to play deserves assessment.
If an acoustic has changed after dry storage, tell the repairer. Humidity can affect the top and action as well as the neck. Buzz does not by itself tell you to humidify the guitar or turn the truss rod.
Avoid filing frets or nut slots, sanding a saddle, or making trial adjustments just to see whether the sound changes. The setup-assessment guide explains what to bring and what a repairer can check. A useful demonstration includes the affected note, your usual picking strength and the string/tuning information.
Manufacturer references
Fender’s fret-buzz checks cover finger placement, pressure and picking attack. Fender’s setup-specification guidance explains that some minor string noise can occur. Taylor’s string-buzz support page also identifies a defective individual string as a possible contributor. For mechanical adjustments, follow your exact model’s manual.